Power supplies and battery chargers

SAILOR 6081 Power Supply Unit and Charger

The Power Supply Unit and Charger provides DC power at five DC power outlets (all separately fused) and a 15 V DC power outlet for SAILOR 3027 mini-C Transceiver. It also charges automatically a connected battery. If the AC power fails the power supply delivers DC power from the connected battery.

You can access control and monitoring data via the Ethernet interface. There are relay outputs for AC outage and battery voltage alarm.

The power supply provides up to 1480 W in total. The following models are available:

Model Peak output power
SAILOR 6081 Max. 370 W
SAILOR 6081 with 1 additional SAILOR 6080 Max. 740 W
SAILOR 6081 with 2 additional SAILOR 6080 Max. 1110 W
SAILOR 6081 with 3 additional SAILOR 6080 Max. 1480 W
  • Output voltage according to battery requirements (range: 24—31.2 V)
  • 5 VDC output for SAILOR 3027 Terminal
  • DC connectors, 2 × 10 A, 2 × 20 A and 1 × 50 A
  • Up to 1480 W peak output power
  • AC input (100-240 VAC operating) with fuse (6.3 A) with Power Factor Correction
  • Automatic detection of input voltage range
  • AC alarm and battery voltage alarm
  • Ethernet connector for monitoring and control information
  • Battery charging function
  • Short circuit protection
  • Over-temperature protection (shutdown with automatic restart)
  • Switch over to battery power in case of AC supply failure
  • No forced cooling required
  • Link to control up to 8 Power Supply Unit and Charger units connected to the same battery
  • Upgrade on site by service personnel
  • IP 32 for internal high voltage areas (>42 V), IP 22 in other areas when vertically mounted (wall) and connector panel is facing down

Specification:

DC output (nominal): 28 V or according to battery requirements.
Alarm: In case of AC power failure or if battery power is outside allowed range
IP rating in high voltage (>42 V): IP 32 (mounted vertically on wall)
IP rating in other areas: IP 22 (mounted vertically on wall)
Compass safe distance: 30 cm
Cooling: No forced cooling required.
Dimensions: 66 × 590 × 355 mm
Weight: 6.2 kg
Temperature:
operating
storage
-15…+55°C
-40…+80°C
Survival temperature (power on): -40…+80°C

 

 

TT-6080A AC/DC Power Supply

The TT-6080A AC/DC Power Supply can deliver 300 W output power on average with a peak of 370 W for a minimum of 2 minutes. This is useful for MF/HF applications and DSC transmissions of 2 minutes duration. It is AC powered with a battery switch-over function.

The AC/DC Power Supply is designed to be used with BGAN-X and FleetBroadband terminals. It can be used as a stand-alone DC power supply or as a building block in a larger power supply. When more power is needed than one power supply can give, i.e. 300 W, you can stack up to three power supplies on top of each other and connect them. When stacking 2 or 3 units the load on each of the units is automatically balanced among the units.

  • Two DC connectors, output, range: 28.7 V – 31.2 V
  • Output power 300 W continuous, 370 W peak (2 min., 100-240 VAC) or 270 W continuous, 333 W peak (2 min., 90-100 VAC)
  • AC input (100-240 VAC operating) with fuse (6.3 A)
  • Automatic selection of input voltage range
  • AC alarm and On/off switch
  • Daisy-chaining of up to three units to give up to 900 W
  • Short circuit protection
  • Over-temperature protection (shutdown with automatic restart)
  • Battery switch-over in case of AC supply failure, secured by 2 fuses (30 A)
  • No forced cooling required
  • IP 3X for internal high voltage areas (>42 V), IP 2X in other areas
  • IP X2 when vertically mounted (wall) and connector panel is facing down

Specification:

Output power @100-240 VAC: 300 W continuous
370 W peak (2 min.)
Output power @ 90-100 VAC: 270 W continuous
333 W peak (2 min.)
DC output (nominal): 31.2 VDC at 0A
29.3 VDC at 10A
28.7 VDC at 13A
AC input voltage: 115-230 VAC nominal,
100-240 VAC operating
Alarm in case of: AC power failure
IP rating in high voltage (>42 V): IP 3X
IP rating in other areas: IP 2X
IP rating when mounted vertically on a wall: IP X2
Cooling: No forced cooling required.
Dimensions: 46.5 × 354 × 265 mm
Weight: 3.7 kg
Temperature:
operating
storage
-20…+55°C
-40…+80°C

 

 

Unicont AU-106 Remote signaling module

Remote signaling module AU-106 connected to the devices with output based on relay’s “dry contacts” closing or breaking. Also AU-106 has an input to connect devices with signaling output based on output DC or AC voltage to indicate failure. AU-106 provides for visual and sound signaling and allow its check-back.

  • Signaling support based on relay’s “dry contacts” closing/breaking.
  • Signaling support based on DC or AC voltage output on failure.

Specification:

Current consumption on signaling input: no more than 2 mA
Power voltage: 12…24 VDC
Dimensions: 88 × 108 × 54 mm
Weight: no more than 500 g

 

 

Unicont AU-206 Alarm Unit

Alarm unit AU-206 is meant for visual and acoustic warning of navigator on activation of external alarm of any ship’s equipment connected to alarm unit on the basis of disconnection of “dry” contacts.

Specification:

Power consumption: no more than 3 W
Power voltage: 9…36 VDC
Inputs number: 5
Inputs type: Dry contacts disconnection sensor
Power output voltage: Equal to power supply voltage
Weight: 0,7 kg (max)
Dimensions: 120 × 130 × 51,5 mm
Temperature:
operating
storage
-25…+55°C
-55…+75°C

 

 

Unicont BMU-126 Battery Measuring Unit

The battery measuring unit BMU-126 is intended for measuring parameters of a ship’s battery (during normal operation, charging and discharging periods). The device measures analogue values such as current and voltage, converts them into digital and send data to remote indicators in digital messages via RS-422 interface.

There are 2 remote indicators for BMU-126 based on DR-209 and UCB-91:

  • DR-209BP indicator provides adjustable user interface and advanced functionality such as graph drawing.
  • UCB-91BP indicator is a low-cost solution. It provides simple displaying current state of a battery only.

Specification:

Input voltage: 9…36 VDC
Measured voltage: 9…36 VDC
Measured current: 0…50 A
Power consumption: 2,5 W (max)
Inputs/outputs: Battery input (for battery connection)
Battery output (for load connection)
Charger input
Battery panel input/output
Dimensions: 221 × 48 × 201 mm
Weight: 3 kg (max)
Temperature:
operating
storage
-20…+55°C
-55…+70°C
Protection index: IP 22
DR-209BP battery panel: Big graphical LCD display (114×64 mm viewable area) with 240×128 resolution
UCB-91BP battery panel: Text mode (16×2 symbols) only

 

 

Unicont BPS-114 Uninterruptible power supply unit

Uninterruptible power supply unit BPS-114 is intended for permanent supply various ship and industrial equipment with the stabilized voltage of a direct current 14.5 V. Embedded high capacity battery provides power supply of connected equipment more than 60 minutes after fall of the incoming voltage (110/220 VAC).

  • Indication of battery charge level with LED bar
  • Current state indication with LED color (green – charging, red – discharging)
  • Indication and audio signaling of low battery level
  • Protection against battery’s deep discharge

Specification:

Input voltage: 110/220 VAC
Output voltage (operating from input circuit 110/220 VAC): 14.5 VDC
Output voltage (operating from embedded battery): 9.6…13.5 VDC
Nominal load current (operating from input circuit 110/220 VAC): 14 A
Nominal power: 200 W
Time of operation from embedded battery: not less than 60 minutes
Efficiency: not less than 70%
Dimensions: 270 × 380 × 115 mm
Weight: 10 kg
Temperature:
operating
storage
-10…+50°C
-20…+60°C
Protection index: IP 22

 

 

Unicont BPS-114-24 Uninterruptible power supply unit

Uninterruptible power supply unit BPS-114-24 is intended for permanent supply various ship and industrial equipment with the stabilized voltage of a direct current 24 V. Embedded high capacity battery provides power supply of connected equipment more than 60 minutes after fall of the incoming voltage (110/220 VAC).

  • Indication of battery charge level with LED bar
  • Current state indication with LED color (green – charging, red – discharging)
  • Indication and audio signaling of low battery level

Specification:

Input voltage: 110/220 VAC
Output voltage (operating from input circuit 110/220 VAC): 27.5 VDC
Output voltage (operating from embedded battery): 19.2…24.8 VDC
Nominal load current (operating from input circuit 110/220 VAC): 12 A
Nominal power: 300 W
Time of operation from embedded battery: not less than 60 minutes
Efficiency: not less than 70%
Dimensions: 295 × 410 × 205 mm
Weight: 16 kg
Temperature:
operating
storage
-10…+50°C
-20…+60°C
Protection index: IP 22

 

 

Unicont CH-105 Automatic battery charger

The automatic battery charger CH-105 is used to charge ship batteries. Soft and handy tuning of device’s output current and voltage, its high maximum power allow to use the device with ship batteries of capacity up to 200 A/h. UCB-91BP or DR-209BP can be used for remote control of CH-105 and indication of charging voltage and current. Embedded sound and visual signaling.

  • Type approved by the Russian Maritime Register Of Shipping.
  • Two digital LEDs indicators to display charging voltage and current values.
  • 3 LEDs for device’s current state indication: charging, normal, failure.
  • Easy-to-use fastenings provide its simple mounting and installation.
  • Automatic overload and battery connection reversed polarity protection.

Specification:

Input voltage: 110/220 VAC, 50/60 Hz;
24VDC(option);
110 VDC(option);
220VDC(option)
Floating charging voltage: Adjustable, 9..30 VDC
Maximal charging current: Adjustable, up to 20 A
Normal batteries’ capacity: 40-200 A/h
Normal charging time: no more than 10 hours for 80% capacity
Dimensions: 345 × 265 × 140 mm
Weight: no more than 7 kg
Temperature:
operating
storage
-20…+55°C
-55…+70°C

 

 

Unicont DC-108 DC/DC converter

The device DC-108 is used for galvanic isolation of the connected equipment from ship’s power circuit, also it is used for VDC conversion.The device is produced in a range of different input and output voltage and power values. Electrical scheme of the device has automatic protection against short circuit and overload.

Specification:

Input voltage values: 19…36 VDC,
36…72 VDC,
72…144 VDC
Output voltage values: 12 VDC,
24 VDC
Max. current: 12.5 A,
6.3 A
Nominal power: 150 W
Isolation resistance: 100 МΩ on 500 V
Dimensions: 169 × 245 × 59.5 mm
Weight: no more 2 kg
Temperature:
operating
storage
-10…+60°C
-30…+70°C

 

 

Unicont PCH-205 Power Supply/Battery Charger

The automatic battery charger / power supply PCH-205 is used to charge ship’s batteries and power supply ship’s equipment simultaneously. It’s high maximum power allows to use the device with ship batteries of up to 200 A/h capacity and supply connected equipment with 24 V of a direct current up to 20 A at the same time.

  • Sound and visual signaling on too high voltage (over voltage) or too low voltage of a battery.
  • 3 LEDs for device’s current state indication: Charging, Normal, Failure
  • Automatic overload protection
  • Automatic protection against short circuit
  • Protection against reversed polarity connection of a battery.
  • Temperature correction of charging voltage.

Specification:

Input voltage: 110/220 VAC
Charging voltage: 28,5 VDC
Charging current: 20 A (max)
PS output voltage: 24 VDC
PS output current: 20 A
Normal batteries’ capacity: 40-200 A/h
Normal charging time: no more than 10 h
Dimensions: 345 × 125 × 320 mm
Weight: 14 kg (max)
Temperature:
operating
storage
-20…+55°C
-55…+70°C
Protection index: IP22

 

 

Unicont PS-103-20A Power supply unit 110/220VAC/24VDC

Power supply unit PS-103-20A is intended to supply various ship and industrial equipment with the unstabilized voltage of direct current 24 V. Easy-to-use fastenings provide its simple mounting and installation. Automatic switching over to backup power supply in case of input voltage failure. In order to provide visual and sound signaling AU-106 or AU-206 units can be connected to the alarm output. Galvanic isolation of the input circuit from the output circuit. Type approved by the Russian Maritime Register Of Shipping.

Specification:

Input voltage: 110/220 VAC
Output voltage: 24 VDC
Nominal load current: 20 A
Maximum load current: 25 A
Nominal power: 500 W
Maximum power: 600 W
Efficiency: 93%
Maximum pulsation: no more than 0,7 V
Dimensions: 270 × 380 × 115 mm
Weight: 12 kg
Temperature:
operating
storage
-20…+55°C
-60…+70°C
Protection: IP 22

 

 

Unicont PS-103-7A Power supply unit 110/220VAC/24VDC

Power supply unit PS-103-7A is intended to supply various ship and industrial equipment with unstabilized voltage of a direct current 24 V. Automatic switching over to backup power supply in case of input voltage failure. Small overall dimensions and easy-to-use fastenings provide its simple mounting and installation. In order to provide visual and sound signaling AU-106 or AU-206 units can be connected to the alarm output. Galvanic isolation of the input circuit from the output circuit. Type approved by the Russian Maritime Register Of Shipping.

Specification:

Input voltage: 110/220 VAC
Output voltage: 24 VDC
Maximum load current: 5.5 A
Nominal power: 170 W
Maximum power: 200 W
Efficiency: 93%
Maximum pulsation: no more than 0,5 V
Dimensions: 156 × 231 × 95 mm
Weight: 4.5 kg
Temperature:
operating
storage
-20…+55°C
-40…+70°C
Protection: IP 22

 

 

Unicont PS-203 Power supply unit

Power supply unit PS-203 is intended to supply various ship and industrial equipment with stabilized voltage of a direct current 24 V (12 V, 48 V – depends of model). Small overall dimensions, weight and easy-to-use fastenings provide its simple mounting and installation. Fan less construction of the device provides long meant time between failures and silent operation. The device is produced in several modifications: with different output voltage (12, 24, 48 V) and maximal power (50 W, 150 W, 300 W).

Specification:

Input voltage: 110/220 VAC
Output voltage: 12 or 24 or 48 VDC, depending of model
Output power: 50 or 150 or 300 W, depending of model
Dimensions: 169 Ѓ~ 245 Ѓ~ 59.5 mm
Weight: 3 kg (max)
Temperature:
operating
storage
-20…+55Ѓ‹C
-60…+70Ѓ‹C
Protection: IP 22
Isolation resistance: 100 „MW on 500 V

 

 

Unicont PS-303 Dual Input Power Supply Unit

The PS-303 power supply is designed to supply 24 V(or 12 V) stabilized voltage to various marine or industrial equipment. PS-303 has 2 inputs for connection of power sources. When 1st input fails device switches to 2nd input and continue operation. Small overall dimensions and easy-to-use fastenings provide it’s simple mounting and installation. LED indication of primary/secondary power input condition.

Specification:

Input voltage (input #1):
PS-303-A2-2
PS-303-A2-1
PS-303-A1-1
PS-303-22-1
PS-303-22-2
PS-303-21-1
PS-303-11-1
220 VAC
220 VAC
220 VAC
24 VDC
24 VDC
24 VDC
12 VDC
Input voltage (input #2):
PS-303-A2-2
PS-303-A2-1
PS-303-A1-1
PS-303-22-1
PS-303-22-2
PS-303-21-1
PS-303-11-1
24 VDC
24 VDC
12 VDC
24 VDC
24 VDC
12 VDC
12 VDC
Output voltage:
PS-303-A2-2
PS-303-A2-1
PS-303-A1-1
PS-303-22-1
PS-303-22-2
PS-303-21-1
PS-303-11-1
24 VDC
12 VDC
12 VDC
12 VDC
24 VDC
12 VDC
12 VDC
Max. output current:
PS-303-A2-2
PS-303-A2-1
PS-303-A1-1
PS-303-22-1
PS-303-22-2
PS-303-21-1
PS-303-11-1
4,2 A / 6,5 A / 12,5 A
8,5 A
12,5 A / 25 A
8,5 A
4,2 A / 14,6 A
12,5 A / 27,5 A
4,1 A
Power:
PS-303-A2-2
PS-303-A2-1
PS-303-A1-1
PS-303-22-1
PS-303-22-2
PS-303-21-1
PS-303-11-1
100 W / 156 W / 300 W
100 W
150 W / 300 W
100 W
100 W / 350 W
150 W / 330 W
50 W
Dimensions: 285 × 245 × 82 mm
Weight: 10 kg (max)
Temperature:
operating
storage
-20…+55°C
-60…+70°C
Protection: IP 22